China Professional New Small Motor Grader Tire Gr100 100HP Motor Grader Gear Shift with Good quality

Product Description

New Small Motor Grader Tire GR100 100hp Motor Grader Equipment Change

Motor Grader Parameters 

one,Energy system
Motor of GR100 is CZPT 4BTA3.9-C100-II(S011847) .particular drive axle permit power match of transmission program a lot more sensible and trustworthy.

two,Transmission technique
Transmission and torque converter are electronic-control counter-shaft power-change transmission. Torque converter has massive torque ratio, high efficiency and broad higher efficiency spot. Much better mixed perform qualities can be attained when the torque converter is matched with motor. Transmission has 6 ahead gears and 3 reverse gears. It has CZPT start off defense perform. Gears will be effortlessly shifted by electrohydraulic handle. In the course of equipment shift procedure, there is no impact, pace ratio distribution is affordable, and a variety of operate demands can be content. 

three,Brake method
Brake system includes provider brake method (particularly foot brake) and parking brake program (specifically hand brake). Support brake program is a double-loop hydraulic brake program, it is acted on 4 center rear wheels of grader with protected and reliable brake. Parking brake technique is composed of operator and brake, wherein the brake is mounted on the output finish of the energy control box, and center and rear wheels can be stopped via working hand brake take care of. 

4,Front axle
Entrance axle is a steering axle. The axle can swing to remaining and right. To increase the maneuverability and more minimize turning radius, besides front-wheel steering, articulated frame is adopted, which can even more lessen turning radius. 

5,Doing work device
The functioning gadget of the grader comprises traction body, turning ring, scraper knife and corner gauge. Spherical hinge is organized on the front conclude of the traction frame, it is articulated with the entrance conclude of body, and for that reason, traction body can be rotated and swung close to spherical hinge in any course. Turning ring is supported on traction frame, it can be rotated all around traction frame underneath the pushed of rotary driving device, so as to travel scraper to rotate again. An higher and a reduced slide rails at the again of scraper are supported on chutes of 2 lateral corner gauges, they can laterally slide below the pushing of sideshift cylinder of scraper knife. Corner gauges on 2 sides undertake integral buildings. Their decrease parts are articulated with the decrease finishes of wing plates on 2 sides, their middle parts are linked with one cylinder to adjust swing angle of corner gauge, so as to generate scraper knife to modify soil scraping angle, and the construction can empower soil scraping angle to be modified for 40° in entrance and 5° at back again. 

PARAMETER SPARE

Fundamental specification
Motor model 4BT3.9
Rated electrical power/pace 75/2400kw/rpm
Dimension(LxWxH) 6880×2375×3150mm
Working fat(Regular) 7000kg
Performance specification
Travelling speed ,ahead five,ten,twenty,39km/h
Travelling velocity ,reverse 8,25km/h
Tractive power(f=.75) 41.6KN
Max. gradeability 20%
Tire inflation strain 350KPa
Working hydraulic force 16MPa
Transmission strain one.3~1.8MPa
Operating specification
Max. steering angle of entrance wheels ±50°
Max. lean angle of entrance wheels 17°
Max. oscillation angle of front axle ±15°
Max. oscillation angle of equilibrium box  
Body articulation angle ±27°
Min. turning radius making use of articulation five.9m
Biade
Maximum elevate over ground 300mm
Greatest depth of slicing 350mm
Optimum blade place angle 45°
Blade chopping angle 28°-70°
Circle reversing rotation 120°
Moldboard width X top 3048×500mm

 

The function behind the rack is to convert rotational movement into linear motion, the rack runs by way of a pinion (a cylindrical gear that meshes with the rack), so this setup is typically referred to as a rack and pinion. When running gears and racks, gear oil is also very advised to improve overall performance and longevity. We also stock a wide range of metric spur gears and supply practically each electrical power transmission product on the market
There are many varieties of gears, and the most frequent classification strategy is by gear shaft. Typically, there are 3 kinds of the parallel axis, cross-axis, and staggered axis. 1) Parallel shaft gears: which includes spur gears, helical gears, interior gears, racks, and helical racks, and so on. 2) Cross shaft gears: straight bevel gears, spiral bevel gears, zero-degree bevel gears, and many others. 3) Staggered shaft gears: There are staggered shaft helical gears, worm gears, hypoid gears, and so forth.

China Professional New Small Motor Grader Tire Gr100 100HP Motor Grader Gear Shift     with Good quality